|
|
ss-server(1)============
NAME----ss-server - shadowsocks server, libev port
SYNOPSIS--------*ss-server* [-AuUv] [-h|--help] [-s <server_host>] [-p <server_port>] [-l <local_port>] [-k <password>] [-m <encrypt_method>] [-f <pid_file>] [-t <timeout>] [-c <config_file>] [-i <interface>] [-a <user_name>] [-d <addr>] [-n <nofile>] [-b <local_address] [--fast-open] [--mptcp] [--firewall] [--acl <acl_config>] [--mtu <MTU>] [--manager-address <path_to_unix_domain>]
DESCRIPTION-----------*Shadowsocks-libev* is a lightweight and secure socks5 proxy.It is a port of the original shadowsocks created by clowwindy.*Shadowsocks-libev* is written in pure C and takes advantage of libev toachieve both high performance and low resource consumption.
*Shadowsocks-libev* consists of five components.`ss-server`(1) runs on a remote server to provide secured tunnel service.For more information, check out `shadowsocks-libev`(8).
OPTIONS--------s <server_host>::Set the server's hostname or IP.
-p <server_port>::Set the server's port number.
-k <password>::Set the password. The server and the client should use the same password.
-m <encrypt_method>::Set the cipher.+*Shadowsocks-libev* accepts 21 different ciphers:+table, rc4, rc4-md5, aes-128-cfb, aes-192-cfb, aes-256-cfb,aes-128-ctr, aes-192-ctr, aes-256-ctr, bf-cfb,camellia-128-cfb, camellia-192-cfb, camellia-256-cfb, cast5-cfb, des-cfb,idea-cfb, rc2-cfb, seed-cfb, salsa20, chacha20 and chacha20-ietf.+The default cipher is 'rc4-md5'.+If built with PolarSSL or custom OpenSSL libraries, some ofthese ciphers may not work.
-a <user_name>::Run as a specific user.
-f <pid_file>::Start shadowsocks as a daemon with specific pid file.
-t <timeout>::Set the socket timeout in seconds. The default value is 60.
-c <config_file>::Use a configuration file.+Refer to `shadowsocks-libev`(8) 'CONFIG FILE' section for more details.
-n <number>::Specify max number of open files.+Only available on Linux.
-i <interface>::Send traffic through specific network interface.+For example, there are three interfaces in your device,which is lo (127.0.0.1), eth0 (192.168.0.1) and eth1 (192.168.0.2).Meanwhile, you configure `ss-server` to listen on 0.0.0.0:8388 and bind to eth1.That results the traffic go out through eth1, but not lo nor eth0.This option is useful to control traffic in multi-interface environment.
-b <local_address>::Specify local address to bind.
-u::Enable UDP relay.
-U::Enable UDP relay and disable TCP relay.
-A::Enable onetime authentication.
-6::Resovle hostname to IPv6 address first.
-d <addr>::Setup name servers for internal DNS resolver (libudns).The default server is fetched from '/etc/resolv.conf'.
--fast-open::Enable TCP fast open.+Only available with Linux kernel > 3.7.0.
--mptcp::Enable Multipath TCP.+Only available with MPTCP enabled Linux kernel.
--firewall::Setup firewall rules for auto blocking.
--acl <acl_config>::Enable ACL (Access Control List) and specify config file.
--manager-address <path_to_unix_domain>::Specify UNIX domain socket address for the communication between ss-manager(1) and ss-server(1).+Only available in server and manager mode.
--mtu <MTU>::Specify the MTU of your network interface.
--mptcp::Enable Multipath TCP.+Only available with MPTCP enabled Linux kernel.
-v::Enable verbose mode.
-h|--help::Print help message.
EXAMPLE-------It is recommended to use a config file when starting `ss-server`(1).
The config file is written in JSON and is easy to edit.Check out the 'SEE ALSO' section for the default path of config file.
....# Start the ss-serverss-server -c /etc/shadowsocks-libev/config.json....
INCOMPATIBILITY---------------The config file of `shadowsocks-libev`(8) is slightly different from originalshadowsocks.In order to listen to both IPv4/IPv6 address, use the following grammar inyour config json file:....{"server":["::0","0.0.0.0"],...}....
SEE ALSO--------`ss-local`(1),`ss-tunnel`(1),`ss-redir`(1),`ss-manager`(1),`shadowsocks-libev`(8),`iptables`(8),/etc/shadowsocks-libev/config.json
|
